收藏本站
Precautions
General Precautions at Designing, for Use and Handling
1. Circuit design precautions
(1) Check the rated performance
After checking the operation and installation environments, design the circuit so that it falls within the rated performance range
stipulated in the catalog specification.
(2) Operating temperature and ripple current
a) Set the operating temperature so that it falls within the range stipulated in the catalog specification.
b) Do not apply current that exceeds the allowable ripple current in the catalog.
(3) Leakage current
Even when the soldering conditions fall within the range of the catalog specification, the leakage current increases slightly.
It also increases slightly during high temperature no-load, moisture-proof no-load and temperature cycling tests with
no voltage applied.
In cases such as these, leakage current will decrease by applying voltage in conditions below the maximum operating temperature.
(4) Applied voltage Considerations
a) Make sure the sum of the peak DC voltage and ripple voltage values does not exceed the rated voltage.
b) Please do not apply the reverse voltage to FPCAP .
c) When the DC voltage is low, please check whether the peak value of ripple voltage does not become a reverse voltage.
(5) Reduction of failure stress
The main failure mode of the FPCAP is in the open mode primarily caused by an electrostatic capacitance drop.
Random short circuit mode failures occur rarely.
The time it takes to reach the failure mode can be extended by using the FPCAP with reduced ambient temperature,
ripple current and applied voltage.
(6) Capacitor insulation
a) Insulation is not guaranteed.
b) Be sure to completely separate the case, negative electrode terminal and positive electrode terminal from adjacent components
and PC board traces.
(7) Operating environment
Do not use the FPCAP in the following environments.
a) Places where it can come into direct contact with water or salt water and places where condensation may form.
b) Places filled with noxious gasses such as: hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonia, etc.
c) Places exposed to ozone, ultraviolet rays and radiation.
d) Where severe vibration or shock which exceeds the condition specified in the specification sheets.
(8) Assembly Conditions Considerations
In designing a circuit, the following conditions should be checked before the FPCAP is mounted on the PC board.
a) The pitch and diameter of PCB holes to which the FPCAP is mounted, shall be designed in conformance with the dimensional
tolerance stipulated in the catalog specifications.
(9) PC board
Avoid locating heat-generating components around the FPCAP and on the underside of the PC board under the FPCAP .
(10) Parallel connection
When used in a parallel connection with another capacitor, carefully select the type of capacitor.
(11) Other
a) Electrical characteristics are affected by fluctuations in temperature and frequency.
b) When mounting the FPCAP on a double-sided PC board, design the board so that extra PC board holes are not located
underneath the FPCAP .
2
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
RS80G561MDNASQJT CAP ALUM 560UF 4V 20% RADIAL
RSL0E331MCN1GB CAP ALUM 330UF 2.5V 20% SMD
RSL1E150MCN1GB CAP ALUM 15UF 25V 20% SMD
RSO-4812DZ/H3 CONV DC/DC 1W DL +/-12V OUT SIP8
RSS1C101MCN1GS CAP ALUM 100UF 16V 20% SMD
RSZ-3.33.3/P-R CONV DC/DC 1W 3.3VIN 3.3VOUT
RTS-243.3-R CONV DC/DC 2W 24VIN 3.3VOUT
RU-3.30505/HP CONV DC/DC 1W 3.3VIN 0505VOUT
相关代理商/技术参数
RS80E331MDN1 功能描述:铝有机聚合物电容器 2.5 Volt 330uF 20% RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel
RS80E331MDN1JT 功能描述:CAP ALUM 330UF 2.5V 20% RADIAL RoHS:是 类别:电容器 >> 铝 系列:S8 标准包装:2,000 系列:142 RHS 电容:4700µF 额定电压:10V 容差:±20% 寿命@温度:105°C 时为 2000 小时 工作温度:-40°C ~ 105°C 特点:通用 纹波电流:1.26A ESR（等效串联电阻）:- 阻抗:- 安装类型:通孔 封装/外壳:径向，Can 尺寸/尺寸:0.492" 直径（12.50mm） 高度 - 座高（最大）:1.063"（27.00mm） 引线间隔:0.197"（5.00mm） 表面贴装占地面积:- 包装:散装
RS80E331MDN1PX 功能描述:铝有机聚合物电容器 RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel
RS80E331MDNASQ 功能描述:铝有机聚合物电容器 2.5 Volt 330uF 20% RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel
RS80E331MDNASQJT 功能描述:CAP ALUM 330UF 2.5V 20% RADIAL RoHS:是 类别:电容器 >> 铝 系列:S8 标准包装:2,000 系列:142 RHS 电容:4700µF 额定电压:10V 容差:±20% 寿命@温度:105°C 时为 2000 小时 工作温度:-40°C ~ 105°C 特点:通用 纹波电流:1.26A ESR（等效串联电阻）:- 阻抗:- 安装类型:通孔 封装/外壳:径向，Can 尺寸/尺寸:0.492" 直径（12.50mm） 高度 - 座高（最大）:1.063"（27.00mm） 引线间隔:0.197"（5.00mm） 表面贴装占地面积:- 包装:散装
RS80E471MDN1 功能描述:铝有机聚合物电容器 2.5 Volt 470uF 20% RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel
RS80E471MDN1JT 功能描述:CAP ALUM 470UF 2.5V 20% RADIAL RoHS:是 类别:电容器 >> 铝 系列:S8 标准包装:2,000 系列:142 RHS 电容:4700µF 额定电压:10V 容差:±20% 寿命@温度:105°C 时为 2000 小时 工作温度:-40°C ~ 105°C 特点:通用 纹波电流:1.26A ESR（等效串联电阻）:- 阻抗:- 安装类型:通孔 封装/外壳:径向，Can 尺寸/尺寸:0.492" 直径（12.50mm） 高度 - 座高（最大）:1.063"（27.00mm） 引线间隔:0.197"（5.00mm） 表面贴装占地面积:- 包装:散装
RS80E471MDN1PX 功能描述:铝有机聚合物电容器 RoHS:否 制造商:Panasonic Electronic Components 电容:470 uF 容差:20 % 电压额定值:2.5 V ESR:4.5 mOhms 工作温度范围:- 40 C to + 105 C 端接类型:SMD/SMT 外壳直径: 外壳长度:7.3 mm 外壳宽度:4.3 mm 外壳高度:1.9 mm 封装:Reel